If you’re experiencing issues with your JVC car stereo, a reset often will fix the problem. Resetting a JVC car stereo is a simple process that can be done in no time.
To reset a JVC touchscreen radio, follow these steps:
#1. Locate the reset button on the unit, which is often located behind the radio’s faceplate.
#2. Press and hold the reset button for about five seconds. After a few seconds, the message “RESET” should appear on the screen.
#3. Release the reset button.
#4. After resetting the radio, enter your radio station presets again.
Tip: To reset large screen stereos like KW-Z1000W (link to Amazon), you must reboot it through the settings.
To do this, go to the Settings menu of your JVC radio and select “System Reset.” When prompted, choose “Yes” to reset the device.
In the article below, I explain How to reset a JVC radio and give some tips to keep in mind when resetting a JVC car stereo.
How do I Reset JVC Radio?
Resetting a car radio can be a helpful troubleshooting step if you’re experiencing issues with your audio system.
It’s a simple process that can often fix common problems, such as a frozen screen or lost radio station presets.
To make it quick, follow the steps below:
#1. Locate the Reset Button
To reset your JVC radio, you’ll need to locate the reset button on the unit.
Depending on the specific model of your radio, the reset button may be located in a different spot. For example, on some models, the reset button is located on the side or bottom of the unit, and touchscreen models do not have a button but a small pinhole instead.
Consult your owner’s manual or the manufacturer’s website for specific instructions on locating the reset button on your radio.
#2. Press and Hold the Reset Button
Once you’ve found the reset button, press and hold it for about five seconds.
After that, you should see the message “RESET” appear on the radio’s display.
Hold the reset button for the full five seconds to ensure the reset process is completed correctly.
If you release the button too soon, the reset may not take effect, and you’ll need to do it again.
#3. Release the Reset Button
After you see the “RESET” message on the radio’s display, you can release the reset button.
The reset process is complete, and your radio should return to its factory settings.
#4. Enter Radio Station Presets (If Necessary)
Depending on the specific model of your radio, you may need to enter your radio station presets again after resetting the unit.
This is because the reset process will erase any saved radio station presets and any other personalized settings you may have made to the radio.
To enter your radio station presets, tune to the desired station and press and hold one of the preset buttons until you hear a beep. Repeat this process for each preset station you want to save.
Check for Any Underlying Issues With the Car’s Electrical System
Before resetting your JVC touchscreen radio, it’s important to ensure that your car’s electrical systems are functioning properly.
If you are experiencing issues with your car’s battery or alternator, resetting the radio may not solve the problem if the power goes up and down.
To check the health of your car’s battery, you can use a multimeter to measure the voltage.
A healthy battery should have a voltage of around 12.6 volts when the car is off and around 13.7-14.7 volts when the vehicle is running.
If the battery voltage is significantly lower than these values, it may be time to replace it.
Similarly, you can use a multimeter to test the alternator by measuring the voltage at the battery while the car is running. A healthy alternator should produce a voltage of around 13.7-14.7 volts.
Conclusion
In summary, resetting a JVC radio is a simple process that often fixes common issues with the unit.
To reset your radio, locate the reset button, press and hold it for about five seconds, release the button, and enter any necessary radio station presets.
If you are experiencing issues with your car’s electrical system, check for and address any underlying problems before resetting the radio.
Consult the owner’s manual or contact a qualified technician if you need further assistance.
FAQ
Where Is the Reset Button Located on a JVC Radio?
The reset button is usually located behind the faceplate of the radio. However, depending on the specific model, it may be found in a different spot, such as on the side or bottom of the unit.
How Long Should I Hold the Reset Button?
Hold the reset button for the full five seconds to ensure the reset process is completed correctly.
If you release the button too soon, the reset may not take effect, and you’ll need to start the process over again.
What Happens After I Reset My JVC Radio?
After resetting your JVC radio, it should be returned to its factory settings.
This means that any personalized settings or saved radio stations will be erased, so you may need to enter these again.
What Should I Do if the Reset Process Doesn’t Work for My Radio?
If the reset process does not work for your JVC radio, consult the owner’s manual or contact a qualified technician for further assistance.
The reset process may vary slightly depending on the specific model of your radio, so it’s always a good idea to check with the manufacturer if you need help.